Parker Chilcoat

About Parker Chilcoat

Posts by Parker Chilcoat:

October 18 2023

Industrial Factory Foundation Repair-Victoria Texas

Parker Chilcoat Concrete Leveling, Foundation Repair

Project Type: Void Fill, Slab Stabilization, & Concrete Repair

Location: Victoria, TX

Problem:

A commercial manufacturing company in Victoria, TX contacted C.A.T.FOAM regarding a deteriorating section of their warehouse foundation, needing immediate attention. This particular area of compromised concrete was absolutely vital to the smooth operation of their facility, as it provided essential load-bearing strength for the support columns of their 10-ton overhead crane. Situated alongside the east side wall of the warehouse, the crane structure recently failed its annual OSHA compliance inspection due to misalignment and severe damage to multiple concrete footers. With the crane now out of commission, the client urgently sought the expertise of C.A.T.FOAM for professional assistance.

Analysis:

After consulting with the owner & shop manager and inspecting the affected area, C.A.T.FOAM discovered the settlement issues were due to soil loss and erosion of the slab’s supporting soils. The area also had consistent cracking defects from heavy storage of steel-coil rolls. Damage from Hurricane Harvey allowed rainfall to infiltrate the foundation’s supporting soils on the east side, causing washout through the warehouse’s precast walls. To address these issues, C.A.T.FOAM collaborated with MacGyvered Engineering & Contractors to develop a three-stage repair strategy using foam injection technology among other methods. This strategy also involves realigning the overhead crane and replacing three irreparably damaged concrete footers. The goal is to effectively resolve the problems with minimal disruption to facility operations.

Solution:

C.A.T.FOAM and MacGyvered Engineering have successfully addressed void issues under the 5-inch concrete slab and restored strong support to the foundation. By injecting high density polymers and following a systematic injection plan, we effectively filled the affected area. We then leveled the defective overhead crane structure to meet CMMA tolerance requirements by raising each crane column and installing steel shims. New anchor bolts were securely installed at each column base, and mortar was applied around the base plate. Finally, we fully replaced three inadequate concrete footers using standard construction methods, reinforcing the crane columns with custom brackets and cribbing blocks before demolition.

Conclusion:

In just two weeks, C.A.T.FOAM and MacGyvered’s team successfully completed the factory’s rehabilitation project, all within the regular business hours. The client was extremely satisfied as the 10-ton overhead crane structure swiftly passed the rigorous OSHA inspection and was promptly restored to full operational service. Our team addressed the problem areas, employing a clever solution that saved valuable time and money by eliminating the need to disassemble the entire overhead crane system.

July 12 2023

UFP Industries-Loading Area Rehabilitation

Parker Chilcoat Concrete Foam Injections

Project Type: Soil Stabilization & Releveling

Location: New Waverly, TX

Problem:

UFP Industries is a multibillion-dollar forestry products manufacturer and supplier, with 221 facilities worldwide. Their plant in New Waverly, TX had recently constructed an area experiencing major defects in the concrete slab’s infrastructure. This affected area consisted of over a hundred thousand square feet (ft2) of twelve inch thick reinforced concrete slabs designed to support high flow, heavy class-5 forklift traffic. Due to being built on top of an old lumber ash pit, the soil conditions were poor. Therefore, when the concrete pavement was installed, the subgrade was not stabilized adequately for the intended use. From our inspection, we discovered extensive water infiltration through the expansion joints of the concrete causing the supporting soils to become saturated. The continuous heavy forklift and 18-wheeler traffic caused the groundwater to rise to the surface, exit through the expansion joints, and wash out the subgrade. This left voids underneath the concrete which created slab deflection, differential settlement, and eventual failure.

Summary:

The facility had replaced portions of completely failed concrete but were seeking an alternative solution for the areas that could be rehabilitated. The replacement process was extremely invasive to their operations. This downtime caused major delays and revenue losses for the company. C.A.T.FOAM personnel determined that polymer injection technology would provide an ideal solution for the ongoing soil issues, and that all the proposed work could be completed without interrupting the facility’s normal operations. C.A.T.FOAM consulted with civil engineers to develop the injection schematics, specifications, and timeline of the project. An economic proposal was submitted and approved by UFP Industries to begin production.

Solution:

C.A.T.FOAM designed a work schedule and injection schematic that best fit the facilities needs. By utilizing the Foamjection™ process, we were able to compact, consolidate, and reduce the permeability of the soil mass along the expansion joints. This process consisted of injecting hydro-insensitive polymers of high density into the soils supporting the problematic areas. Dynamic Cone Penetrometer (DCP) testing was performed and elevation monitoring devices were utilized by C.A.T.FOAM’s team, ensuring the injections were in accordance with the project design.

Conclusion:

C.A.T.FOAM successfully completed the remediation work in a short, two week period. The problematic areas were treated, and the concrete slab deflection was reduced within the tolerable standards. As an added bonus, we were able to complete this job while avoiding heavy traffic times and the facility could maintain the steady flow of forklift and 18-wheeler traffic.

June 7 2022

Seawall / Bulkhead Repair Case Study Using Deep Foamjection™

Parker Chilcoat Bulkhead Repair, Seawall Repair

Project: Matagorda seawall repair due to deterioration of concrete seawall and bulkhead

Size: Eighty-eight linear feet of seawall.

Time To Complete: 30 hours (a day and a half)

Problem: Concrete Seawall Deterioration in Matagorda

Concrete Alignment Technology (CAT Foam) was contacted by a gentleman who was looking for options to repair his failing concrete seawall for his bay home in Matagorda, TX. The home was located on a canal that connects directly to the Gulf Intracoastal Waterway. The non-stop commercial traffic, consisting of tugboats pushing massive 300-ton steel barges, created a constant displacement of water in the canal which caused the concrete seawall to deteriorate and allow water infiltration. Due to this continuous water movement, the base soil was washed out and voids began to develop below the seawall. Once the support soils were lost, sinkholes or settlement of soils along the seawall became apparent.

Summary: Benefits of Matagorda Seawall Repair with CAT Foam Polyurethane Foam Injection

The homeowner was exploring other solutions such as the replacement of the entire length of the seawall. He was stunned when he received a quote from a local company for just over $34,000 to replace the concrete seawall. Our polyurethane injection process helped the owner avoid the costly hassle of dealing with coastal marine contractors and the time-consuming process of seawall replacement. After the initial walkthrough of the property, the CAT Foam team inspected the area, and it was determined that eighty-eight linear feet of bulkhead were failing and in need of repair.
This saved the customer $24,500, increased the useful life of the seawall structure, and minimal invasiveness of the area receiving treatment.

Solution: Affordable Seawall Repair Delivered On-Time and Within Budget

CAT Foam used the Deep Foamjection™ process to stabilize the soils and prevent further erosion and loss of soil without excavating or damaging the seawall. Deep Foamjection™ is the process of injecting high-density foam to specified depths to reestablish and increase the load-bearing capacity of the soils. The material used for this project was HMI’s expansive polyurethane 402-HydroFoam. HydroFoam was chosen due to its unique hydro-insensitive polymers that aggressively seek out voids and maintain dimensional stability in wet environments.

For this Matagorda seawall repair project, CAT Foam installed twenty-one injection points along the seawall at depths of approximately 3ft and 6ft under the ground. The entire process was completed in a day and a half, and CAT Foam provided a cost-effective solution.

For a free estimate on Matagorda seawall repair or concrete lifting & leveling, call CAT Foam at (800) 595-1880

May 14 2022

Concrete Seawall Repair-Galveston Texas

Parker Chilcoat Seawall Repair, Bulkhead Repair, Void Fill

Project Type: Concrete Seawall Repair, Void Fill

Location: Galveston, TX

Problem:

Concrete Alignment Technology (C.A.T.FOAM) was called by a homeowner who noticed some erosion behind the concrete seawall at his bay home in Galveston, TX. The property was located on a canal which connects to Galveston Bay. Due to poor rainwater drainage around the home, tidal movement, among other variables, there was an extreme loss of soils around the property. This erosion had created a substantial void and cavity underneath portions of the home’s foundation and the entire 110 linear feet of sidewalk that connects to the seawall barrier cap. Furthermore, after performing multiple soil tests along the seawall barrier, using a Dynamic Cone Penetrometer, the soil testing report indicated weak soils at the 6.5 ft depth which was calculated to be just below the water level at high tide. It was also noted that the location of the voids and unstable soils were consistent with the seams where the concrete panels were joined.

Summary:

The homeowner had already explored other options to repair his failing seawall but was unsatisfied with the price. One of the alternatives was quoted to be well over $50,000 and a minimum of 3 weeks to complete. The alternative option would have required an extremely invasive process of ripping up the entire connecting sidewalk and excavating around the home and seawall. The homeowner decided to go with C.A.T.FOAM’s non-invasive option which included a two stage process using HMI™ polymer resin technologies. Firstly, stabilizing the deeper subgrade soils followed by filling the large voids and cavities underneath the connecting sidewalk and home’s foundation.

Solution:

C.A.T.FOAM completed the soil stabilization process using HMI’s Deep Foamjection™ method. The Deep Foamjection™ method consisted of injecting high density polyurethane foam to specified depths behind the seawall in order to reestablish the load-bearing capacity of the soils and sealing the concrete panels from future water intrusion. The material used for this stage of the project was HMI’s expansive polyurethane 402-HydroFoam due to its tremendous hydro-insensitive polymers and ability to set up in wet environments. For the soil stabilization stage, a total of 22 injection points were installed behind the seawall and approximately 55-70 lbs of foam was pumped per injection point at specified depths of 6.5 ft and 3.5 ft into the subgrade. A total of 1,300 lbs of 402-HydroFoam material was installed along the seawall barrier. The second stage of the project, void filling, was completed using FillRite Technologies FillFoam™ material which is a pre-expanded flowable foam engineered for large void fills and soil stabilization applications. FillFoam™ is hydro-insensitive, highly versatile, and is an excellent engineered material for soil repairs and improvements. For this stage, a total of 2,180 lbs of FillFoam™ material was installed at a density of 8 lbs/ft3 in order to sufficiently fill the voids underneath the edge of the home’s foundation and underneath the 110 linear feet of connecting sidewalk.

Conclusion:

The two stage process of soil stabilization and void filling was completed in a total of 50 hours, roughly 5 full days of work. The customer was extremely pleased with the success of the project, saving him time and thousands of dollars all while completing the operations with minimal invasiveness to the surrounding environment.

October 29 2021

Best Concrete Foam Leveling for Pool Decks

Parker Chilcoat Concrete Foam Injections

Is your pool deck cracked, sinking, or both? Have you heard of concrete foam leveling? Many pool owners don’t realize how important it is to fix sinking or cracked concrete before it’s too late. You don’t want to end up having to spend thousands on completely redoing your pool deck. The problem with unleveled concrete is that it will lead to water leaks and structural issues later on. That’s why you need to make sure your deck is properly leveled and sealed.

The good news is that many companies out there specialize in foam leveling – CatFoam being one of them! The team at CatFoam has years of experience in foam leveling services, so you know you’re getting quality work when you work with them.

What Is Polyurethane Foam Jacking?

Polyurethane foam is an efficient and effective way of leveling concrete. Foam leveling works by foam being injected underneath the concrete to fill the voids and raise it to its original height. The amount of polyurethane foam used depends on how many holes you need to fill and how high the concrete needs to be lifted. You can use this leveling process for a variety of projects and places, including residential properties, commercial buildings, and industrial sites. You can do foam injections quickly and without making a mess.

Here are some reasons polyurethane foam leveling might be perfect for you.

If you want a clean and quick process. Foam injection doesn’t damage the surface of your concrete and minimizes dust exposure.
Having hard-to-reach voids. Polyurethane foam injections are just what you need if your concrete is cracked deep under the surface because it can reach them!
Filling in cracks. Foam injections can fill all the gaps in your concrete and be made to match the color or coating of your concrete.

Does Concrete Foam Leveling Last?

Polyurethane foam concrete leveling lasts for about 20 years. The foam will eventually deteriorate over time because of exposure to the sun, moisture, storms, etc. For the best results, consider working with professionals. Using professional services will ensure long-lasting durability and a seamless job.

How Much Does Concrete Foam Leveling Cost?

Most foundation repair companies will provide an estimate to determine how much your project will cost. Usually, polyurethane foam injection is very affordable because of how quick and mess-free it is. Instead of paying thousands to get cement repoured, invest in polyurethane foam injections to get your pool deck fixed today.

CatFoam are experts when it comes to polyurethane concrete foam leveling. They have been servicing the Houston area by keeping concrete raised and foundations lifted. Give CatFoam a call today or check out their website if you’re interested in getting your pool deck fixed.

September 16 2021

Best Bulkhead Repair Company in Texas

Parker Chilcoat Bulkhead Repair

Is your home located on the waterfront? Do you need to contact a bulkhead repair company? Then you’ve come to the right place! We know that you want to feel safe in your waterfront property and not have to worry about flooding. Your bulkheads may need repair because of damage received over time, natural disaster damage, or man-made damage. Repairing your bulkheads yourself can be costly and time-consuming, so let a professional take the stress away and repair your bulkheads quickly.

Bulkheads And Why They Matter

Water damage affects thousands of people every year, and that’s why bulkheads are so important. Bulkheads serve as a barrier between your property and a body of water. This barrier mainly helps stop water erosion from ruining your land and house.

If you live in an area prone to floods, you can protect your home with a bulkhead by building one yourself or contacting a company that can install one. Some people think that bulkheads and seawalls are the same, but they are completely different when it comes to appearance, height, and utility.

Seawalls are typically made from cement and steel, while bulkheads are made from wood, vinyl, or steel. While bulkheads protect your land from eroding away, seawalls protect against wave damage.

Bulkhead Repair: How To Know You Need It

If you think your bulkhead needs repair, there are a few things you can do to identify the problem. You can check if your bulkhead needs repair by:

Look for cracks, seams, and holes in the wall. Check if the wood is soft or rotting. Sometimes you can even poke a screwdriver through a crack to see how deep it goes.
Check the condition of your decking. If it is warped, broken, peeled back, or covered in algae, it will need to be replaced.
Sinkholes can also damage your bulkhead. A way to know if a sinkhole is damaging your bulkhead is you’ll start to notice mounds of earth appearing in your water.

Bulkheads are usually sturdier than they appear – even if there are small cracks or holes, it may not be a significant problem. However, if the water is seeping through your bulkhead, it is necessary to fix this as soon as possible before any further damage happens to your land or the surrounding area.

Hire A Reputable Company For Repairs

It can be costly to hire a company for bulkhead repair, but it is worth the investment to avoid problems. Not hiring a professional can cause more damage and cost you even more money. The most cost-efficient way to handle bulkhead repairs is not to let them occur in the first place. You can accomplish this by frequently inspecting your bulkhead, looking for small cracks or holes in the material. Making a commitment to regular inspection and maintenance of your bulkhead will save you money in the long run.

CatFoam of the Greater Houston area can provide professional repair for all your bulkhead needs. Our team also offers a wide variety of other services, including concrete lifting and foundation repair. CatFoam is dedicated to customer satisfaction and keeping our community safe. So contact us today to start the bulkhead repair process.

August 26 2021

The Best Way to Fix Sinking Concrete

Parker Chilcoat Concrete Foam Injections

Do you have sinking concrete?

The sinking process of concrete is a natural occurrence that happens over time. It’s due to the weight of the concrete and can put your building at risk for cracking or collapsing. Luckily there are some ways you can prevent this from happening by injecting foam into the foundation to lift the concrete. This will provide support and stop those pesky cracks altogether!

What are foam concrete injections?

Concrete injections consist of injecting a foam material into the ground to support sinking concrete. The injection process is performed by drilling holes in the foundation and pumping liquid polymer or polyurethane into the ground through a hose.

The foam that is injected into the ground will expand and cause the concrete to float back up to its original position. These injections are great for repairing sinking foundations because they can support large loads of weight! The injections can prevent the formation of cracks in buildings, garages, or homes.

Why do you need to inject foam?

The continuous weight of concrete will cause it to sink. This can be a huge problem, as the resulting damage could lead to cracks in your exterior walls and even collapse! If done correctly, these injections can provide support for your sinking foundation and prevent this from happening altogether!

Foam concrete injections have been found effective at preventing damage to:

Backyard patios
Sidewalks
Front or back cement stairs
The foundation of houses
Driveways
The foundation of businesses
Porches
Pool decks
Anything that involves sinking concrete!

How often should you have foam injections done?

It depends on the size of your project or building. If it’s an entire house, we recommend doing it once every 2 to 5 years to ensure that none of the surrounding areas sink. With smaller projects like patios, sidewalks, or slabs, you can do it whenever you see that theirs a problem.

What happens if you have sinking concrete?

If you leave it by itself, the concrete will continue sinking until it collapses. There are often times when the surrounding areas won’t be affected too much. But if they are, that could lead to some serious problems, especially for your house!

If this problem occurs, there are some signs you may see around your property:

Cracks in exterior walls and flooring (especially near the edges)
Doors and windows that stick or don’t work properly
Damage to interior wall surfaces such as drywall cracking and water seepage
Sloping floors or sloping walls
Cracking concrete

Why should you care?

These cracks are not only unsightly but can be potentially dangerous for anyone entering or exiting your building. They also increase the risk of mold growth inside your home due to excess moisture from increased water seepage in the cracks around your house. You don’t want that!

What are the benefits of foam injections?

Foam concrete injections have been found effective at preventing damage to foundations caused by sinking. This process has also been used to support structures in a large number of industries, and many homeowners use this method because it is fast and easy.

Are there risks associated with foam injections?

Not at all! The injection process consists of polyurethane or liquid polymer material that is non-hazardous, water-resistant, and chemical resistant. It has low toxicity levels, making it safe for the environment while preventing damage to the foundation. Polyurethane foam injections are also very cost-effective and have a quick return on investment.

If you’re concerned about your concrete foundation’s ability to withstand damage from sinking, contact CatFoam of Houston, Texas today! We can do an inspection and give you a quote with no obligations. Our inspectors will come out and determine exactly what the issue is and help put together a plan of action to get your foundation looking new again!

August 20 2021

Seawall Repair: Top Signs of Water Damage

Parker Chilcoat Seawall Repair

The coastal erosion problem is not new. Coastal erosion has been a problem for centuries, and there are many different reasons why it happens. For instance, the sea level can change because of climate change or shifts in global tectonic plates.

But even if we can’t see any obvious cause, you should still be concerned about your property. Water erosion can cause damage to your home and make you feel unsafe. However, this isn’t the only reason why you should pay attention to any erosion problems. Many people have set up seawalls to protect their property from water erosion.

People who have seawalls protecting their coastal properties need to make sure to watch out for damage and considering getting their seawall repaired. Depending on the circumstances, a seawall that requires repair can be very dangerous for anyone living or working on the property.

What are the three types of seawalls?

Vertical Seawalls

These walls are one of the most common ways to fight high-powered waves. Vertical seawalls are similar to fences and are constructed out of either concrete or steel. These walls are easy to design, but they wear down quickly. Usually, you’ll find vertical seawalls where there are calm waters, so they don’t have to be repaired as often.

Curved Seawalls

These seawalls aren’t as tall as vertical seawalls are, but they offer a smooth slope that’s hard for waves to climb over. You may have seen curved seawalls before as steps leading into the water. Curved seawalls reduce turbulence in the water and redirect waves. These seawalls protect against strong waves during extreme weather events like hurricanes.

Mound Seawalls

A mound seawall is a sloped hill with rock and concrete armor. It slows down the waves before they hit the shore but can wear away faster if exposed to too much velocity. These are not for high-energy shores or ones that need protection from extreme weather. Mound seawalls wear away faster than vertical and curved seawalls.

How many years does a seawall last?

One of the biggest concerns people have about a seawall is how long it will last. Although you can’t predict exactly how much time a seawall has, some basic guidelines can help you estimate the lifespan of your seawall.

Luckily, most maintained concrete seawalls should last for 30-50 years, but this information isn’t necessarily true for other constructions. The wear and tear on your wall will depend on several factors, including:

A seawalls thickness – A thicker wall will protect against the ocean’s waves better than one with thin armor (less than 1-inch thick). However, thicker walls also weigh more and may not be able to hold up over time if they aren’t constructed properly.

The type of material used – Seawalls can be made from steel, timber, vinyl, and aluminum. Steel and aluminum are the most durable, but they also cost more than lumber. Wood is affordable, but it wears down quickly when facing rough waves. Vinyl and timber have relatively low costs, but they wear out after a few years of use.

Exposure to waves – Waves that continually hit a wall over time can adversely affect its durability. For example, if one side of the seawall is exposed more than others, it starts developing weak spots that can cause the entire structure to crumble after years of abuse from heavy waves pounding against it.

How to tell if you need your seawall repaired?

After your seawall has been exposed to natural elements for a long period of time, signs of wear and tear are bound to appear. If you notice your wall starting to crack or large chunks of the wall falling away, this means that it is time for repair. Visible rust can also be another sign, as well as bowing or misaligned slabs of your seawall.

Sometimes, you can’t see any cracks or signs of fractures on your wall. Unfortunately, that doesn’t mean it’s not in trouble. Other things can point to seawall problems like sunken piles or loose concrete slabs. If you notice anything out of the ordinary, it should be addressed immediately to prevent any further damage from occurring.

A seawall should be viewed as a long-term investment that needs to be maintained regularly in order to last. Nevertheless, even properly maintained walls will need some occasional repairs. With this information in mind, take a closer look at your property and start inspecting how well the seawall is holding up against erosion and storm damage over time.

Professional Seawall Repair

A seawall in need of professional repair is tough to address on your own. Affordable and trusted, our specialists at CatFoam can be up close and personal with any seawall repair problem. CatFoam is proud to serve the Houston area and offer seawall repairs for anyone in need from Houston to Galveston. Our team can help waterfront properties, and commercial properties protect against soil and water erosion.

Our seawall repair experts will analyze your property and help you determine the best course of action for seawall replacement or repair. We want to keep your property safe and make sure your seawall is functioning as intended. If you see signs of seawall failure, feel free to contact us today.

August 12 2021

Don’t Delay Commercial Concrete Repairs for Your Business

Parker Chilcoat Concrete Repair

Commercial concrete repair can be a lifesaver for your business.

Few things are as important as your commercial property. The reality is that time and weather are inevitably breaking down the strength and beauty of concrete surfaces, from a commercial sidewalk to an Olympic-sized swimming pool.

Commercial concrete repairs are essential aspects of maintaining your business’s success and reputation, and they should not be delayed or put off. There are many reasons why not to postpone these repairs.

Over time, property owners that neglect commercial concrete repair will experience:

Risk of accidents due to slippery sidewalks or uneven surfaces
Inability to use a portion of your property because it’s so unsafe
Unpleasant aesthetics

What’s the cost of neglecting concrete repairs?

Concrete deterioration is as predictable as it is unavoidable. Every day, water and moisture seep into cracks and holes in your commercial concrete surfaces, freeze in winter and expand in summer. These changes in temperature and seasons lead to more cracks, voids, and eventually, crumbling concrete. This process may seem slow and easy to ignore but think about the cost of delaying concrete repairs over time.

It’s not just a matter of appearance. Concrete cracks and voids can really hurt people and damage property as well, which is why any damage should be attended to ASAP with the help of experienced concrete professionals like us.

The concrete on your commercial property may look great from afar but take one step closer, or even worse trip because you stepped in some uneven surface made by deteriorating concrete. This goes beyond aesthetics; this damages public safety too so don’t wait for something bad to happen before calling for our assistance at (800) 595-1880.

In many cases, postponing commercial concrete repairs can lead to a doubling or even tripling of repair bills in the future. If holes are left unplugged and cracks go unpatched, more moisture will seep into your concrete and cause more damages. This moisture creates a vicious cycle that can be avoided with timely concrete repairs.

The sooner you schedule commercial concrete repairs to repair your cracked concrete sidewalks or uneven surfaces, the better off you’ll be. You’ll save yourself from expensive repairs down the road.

How does Deep Foam Injection for Concrete Repair Work?

Concrete Lifting is a process where polyurethane foam material fills any voids and raises the surface. The expansion of this liquid causes it to reach its final volume in seconds without compromising on strength or density. Concrete Lifting/ Leveling with Deep Foam Injection can be done quickly with minimal mess, making it an ideal choice for many projects!

The polyurethane foam used for commercial concrete leveling has expansion properties to fill small cracks or voids. This produces a smoother, more level surface and allows for easier walking and less slipping.

The foam can also resist the natural forces of water freezing, expanding, and contracting as temperatures change through the year.

Why Choose CATfoam for your commercial concrete repair?

If you allow your commercial concrete problems to become worse, you will be spending more money on repairs in the end. It can cost many thousands of dollars for a professional concrete contractor to come and repair your concrete, depending on how severe the damage is. Your concrete can sustain many different types of damages, such as cracks, breaks, and damaged joints. The sooner you deal with these problems, the less money you will spend on repairs in the long run.

Commercial concrete repair is necessary for all business owners. It is essential to know that there are many benefits of seeking help sooner rather than later. If you allow your commercial concrete problems to worsen, you will spend more money in the future on expensive repairs. The best way to avoid this problem is not to delay and to get professional assistance as soon as possible when needed. With CATfoam deep foam injection, you can quickly and easily restore smooth and attractive concrete surfaces in no time at all.

CATfoam provides quality commercial concrete repair services with expertise in complex projects, including cracks, breaks, and damaged joints. Contact us today if you need help repairing or maintaining your commercial property’s concrete surfaces. We provide commercial concrete repair from Conroe to Houston and everywhere in between.

August 1 2021

Top 3 Benefits of Foam for Raising Concrete Driveways

Parker Chilcoat Concrete Raising

In recent years, contractors and homeowners have been using foam for raising concrete driveways. Foam is simple and effective when it comes to raising concrete driveways. It also saves money because the foam can be installed quickly without heavy machinery or large crews needed.

With that said, here are 3 top benefits you will receive if you choose foam over other methods!

Foam is a simple and effective way of raising concrete driveways

Foam is a convenient and easy way to level your concrete driveway When improving the height of a concrete driveway, one option that many people should consider is foam. Foam has proven to be more durable over time than other materials because it does not break down.

Homeowners and contractors alike will find the foam very easy to install. Unlike other methods, foam uses a pump that can inject the foam deep into the ground. The driveway itself can be easily raised with the use of foam by simply injecting it through holes drilled in the concrete and then filled below the slab to lift and level it. Foam comes in a variety of forms, but one of the most popular for concrete raising of driveways is polyurethane.

The driveway itself can be easily raised with the use of foam by simply injecting it through holes drilled in the concrete and then filled below the slab to lift and level it. Foam comes in a variety of forms, but one of the most popular for the concrete raising of driveways is polyurethane.

Polyurethane foam essentially functions as an “inflatable” sponge that expands and fills voids or air pockets. This essentially provides a solid foundation for the driveway as well as ensuring that the integrity of your driveway is not compromised. CatFoam can help you with the foam installation process so that your driveway will be raised as quickly and efficiently as possible.

Foam is very cost-effective and can be completed in days without any need for heavy machinery or large crews

Foam is very cost-effective and can be completed in days without any need for heavy machinery or large crews. It’s also a lot cheaper than other materials, such as pouring concrete to get your driveway higher. While concrete can be effective, you will need a large crew to do the job. This involves renting machinery and paying for labor. Foam is simple to apply for everyone and also has other benefits as well.

Polyurethane foam also allows for proper drainage under the slab so no need to worry about drainage issues. It can be as effective at keeping water away from your driveway. This is a major advantage when compared to other methods of raising the concrete because you do not have to deal with any drainage issues or cracks in your driveway over time.

Raising concrete driveways Conroe TX

Benefits of Foam for Concrete Raising of Driveways

Cost-effective.
Fast process
Save time and energy.
Eco-friendly

What Makes Foam Injection Stand Out?

Foam injection is a simple and cost-effective way of raising your driveway. Other alternatives can be time-consuming and costly. By using foam, you save time and money, while also getting the job done. It drains just like soil so there are no worries about runoff or drainage issues. Foam is also a great alternative for people who are looking to raise their concrete driveways higher but don’t want the hassle of total concrete replacement.

After reading this article, we hope you have a better understanding of the ecological and cost-effective benefits of foam for raising your concrete driveway. In recent years, contractors and homeowners have been using foam to raise their concrete driveways. If you’re looking to save time, money, or energy on the project, then we highly recommend that you use foam infection for concrete raising rather than replacing the driveway. Call Catfoam for a free estimate on raising concrete driveways, sidewalks, steps and more.